Page 2 of 2
Re: Rubber Knob
Posted: Mon Sep 16, 2024 10:35 am
by vjmanzo
Hey @KenanJ—I’m not sure why the STL for the knob is not in the repo, but I have some people looking into it. I’ll let you know when it turns up.
Re: Rubber Knob
Posted: Mon Sep 16, 2024 10:37 am
by KenanJ
vjmanzo wrote: Mon Sep 16, 2024 10:35 am
Hey @KenanJ—I’m not sure why the STL for the knob is not in the repo, but I have some people looking into it. I’ll let you know when it turns up.
Ah! Thank you sir ! I will post the iteration I make and share the best result I can get compared to the Davies I have
Re: Rubber Knob
Posted: Mon Sep 16, 2024 3:35 pm
by ricardomedina
where can I download this stl to print ? thx a lot !
Re: Rubber Knob
Posted: Wed Oct 02, 2024 12:54 pm
by KenanJ
mmmguitar wrote: Sat Sep 07, 2024 6:49 pm
Being as the thread was bumped, I'll mention that I intend to put a set of those Knobeez through their paces in my next Fly project, and share my impressions of whether they live up to the guarantees on the listing page (e.g., that they fit 6mm and 1/4" pot shafts, knurled or smooth, and that they remain secure with push-pull use). However, Roland delaying the release of the gear i intend to use them with means that I can't get to it until some time in this next year.
@mmmguitar just bumping this to confirm that knobeez don’t fit …
Re: Rubber Knob
Posted: Wed Oct 02, 2024 2:02 pm
by mmmguitar
KenanJ wrote: Wed Oct 02, 2024 12:54 pm
@mmmguitar just bumping this to confirm that knobeez don’t fit …
Do they not stay attached to the pot shaft, or do they merely not have the depth to push down as far as the other knobs?
Re: Rubber Knob
Posted: Wed Oct 02, 2024 2:17 pm
by KenanJ
mmmguitar wrote: Wed Oct 02, 2024 2:02 pm
KenanJ wrote: Wed Oct 02, 2024 12:54 pm
@mmmguitar just bumping this to confirm that knobeez don’t fit …
Do they not stay attached to the pot shaft, or do they merely not have the depth to push down as far as the other knobs?
They stay on the shaft but it lacks depth like shown in the picture
Re: Rubber Knob
Posted: Wed Oct 02, 2024 3:57 pm
by mmmguitar
KenanJ wrote: Wed Oct 02, 2024 2:17 pm
They stay on the shaft but it lacks depth like shown in the picture
Thanks. In that case, are there enough threads for the potentiometer nut available to shim the cavity side of the pot shaft with an additional locking washer, to decrease the height of the pot shaft?
I'm referring to these:
Re: Rubber Knob
Posted: Thu Oct 03, 2024 1:19 am
by KenanJ
mmmguitar wrote: Wed Oct 02, 2024 3:57 pm
KenanJ wrote: Wed Oct 02, 2024 2:17 pm
They stay on the shaft but it lacks depth like shown in the picture
Thanks. In that case, are there enough threads for the potentiometer nut available to shim the cavity side of the pot shaft with an additional locking washer, to decrease the height of the pot shaft?
I'm referring to these:
pot lock washer.jpg
I will check Saturday when I receive 10 strings to try out on my 97 supreme that gives me a hard time getting well setup …
Re: Rubber Knob
Posted: Thu Oct 03, 2024 9:47 am
by KenanJ
@mmmguitar do you have a reference for the wahsers? preferably in a metric value ^^
Re: Rubber Knob
Posted: Thu Oct 03, 2024 11:55 am
by mmmguitar
KenanJ wrote: Thu Oct 03, 2024 9:47 am
@mmmguitar do you have a reference for the washers? preferably in a metric value ^^
Those washers (commonly referred to as "locking pot washers" or "star lock washers") generally come in 3/8" (9.525mm) internal diameter. I don't recall if Ken used them in his era of Fly production (can anyone confirm?). In any case, using them to shim the pot shaft height shorter will only work if you have extra, available threads visible past the nut the knob is covering (I'm afraid I don't have a stock '90s Fly to check for myself).
Re: Rubber Knob
Posted: Sat Oct 12, 2024 10:46 pm
by InsideInfo
These are all the washers on the prerefine but no star washers except on the input jack.
